Bw Clip H2s Activation Sequence Again

BW Clip Real Fourth dimension Operator Manual

2 OR 3 YEAR H₂S, CO, O_ii, So₂ SINGLE-GAS DETECTOR

BW Prune Real Fourth dimension is a portable, single-gas detector manufactured by BW Technologies past Honeywell (BW). BW Clip Real Fourth dimension continuously displays the concentration of a specific gas in the ambient environment, and activates an alarm when concentrations exceed alarm setpoints. It is your responsibility to respond appropriately to the alarms. BW Prune Real Time is a member of the GasAlert family unit of products. It is compatible with IntelliDoX and MicroDock II automatic test and calibration stations, as well as Fleet Manager II software version 4.2 or higher. For more than information, visit the product website at world wide web. honeywellanalytics.com

Safety Information: Read First

Alert

1. Exchange of components may impair Intrinsic Safety.
2. BW recommends performing a bump exam prior to each twenty-four hour period'due south use to confirm sensor response and warning activation by exposing the detector to a concentration of target gas that exceeds the depression alarm set up bespeak. BW also recommends performing a crash-land exam if the detector has been subjected to physical impact, liquid immersion, an Over Limit alarm event, custody changes, or anytime the detectors performance is in doubt. Calibrate the detector after a failed bump test. Ever bump test and calibrate in a fresh air environment.
3. Detectors in hibernation mode are not functional.

Caution

1. Activate the detector before the activation date on the bundle.
2. This product is a gas detector, non a measurement device.
3. Ensure that the sensor grill is costless of dirt, debris, and is not obstructed.
4. Clean the outside with a soft, damp cloth.
5. For optimal performance, periodically aught the sensor in a normal atmosphere (20.9% v/v O₂ ) that is gratuitous of chancy gas.
6. Portable safety gas detectors are life condom devices. Accurateness of ambient gas reading(s) is dependent upon factors such as accuracy of the scale gas standard used for scale and frequency of calibration. BW recommends performing a calibration at least once every 180 days (6 months).

Getting Started

LCD and Symbols

Actuate a New Detector

1. Move to a normal atmosphere (20.9% v/v O₂ ) that is complimentary of hazardous gas.
2. Press and hold the pushbutton until a five second countdown is displayed, and then go on to hold until the countdown is complete.
3. When the countdown is complete, the LCD and LEDs plow on and so turn off. The detector performs an internal diagnostic examination.
4. When the diagnostic test is successful, the alarm setpoints are displayed and the LEDs flash.
5. The sensor stabilization countdown is displayed. During the countdown, the detector vibrates continuously for 20 seconds. The time required to stabilize varies depending on sensor type. When the countdown reaches 0, the LEDs flash and the audible alarm beeps.
6. The detector is in normal operating fashion when the gas type and concentration are displayed.

Normal Operating Style

When the detector is in normal operating fashion, the type of gas detected is permanently displayed. The detected concentration of the gas is displayed until it is disrupted by a pushbutton activeness, gas warning, or error issue.

Operating Life

When the detector is activated for the first time, the operating life inaugural is displayed. Press the pushbutton to display remaining operating life.

90 Days or Less Remaining

When the operating life countdown reaches 90 days or less earlier expiry, the inaugural display changes to days. The countdown displays the remaining operating life in days until the countdown reaches 24 hours or less before expiry.

24 Hours or Less Remaining

When the operating life countdown reaches 24 hours or less before expiry, the inaugural display changes to hours, and the Expiry! warning and non-compliance symbol are displayed.

Cease of Operating Life

When the operating life countdown ends, the detector deactivates and detector safe functions are disabled. It is possible to call up event logs for a limited time later decease. The EXPIRY! alert and non-compliance symbol are displayed for up to thirty days afterwards death.

Internal Diagnostic Tests

Activated detectors automatically perform one internal diagnostic test every 24 hours. If the internal diagnostic test fails, the diagnostic fail-prophylactic begins.

Diagnostic Fail-Safety

1. The Decease! warning and non-compliance symbol are displayed.
2. The detector beeps and vibrates.
3. The LEDs flash 2 times per second for fifteen seconds.
4. OFF or an error lawmaking is displayed. The detector is deactivated. Information technology is possible to recollect the event logs for a limited fourth dimension afterwards expiry. If you are unable to recall the event logs, contact BW.

Alarms and Warnings

An alarm is initiated when the sensor is exposed to a gas concentration that exceeds warning setpoints. The alert persists until the alarm gas concentration returns to an acceptable range. Battery life decreases rapidly when the detector is in alarm condition.

Depression Warning

Audible: 1 beep per second

Visual: 1 flash per second

Vibration: 1 vibration per second

High Alarm

Audible: 2 beeps per 2nd

Visual: two flashes per second

Vibration: 2 vibrations per second

Over-Limit and Under-Limit Alarms

If the gas concentration is across the sensor range, OL (over-limit) or -OL (under-limit) is displayed.

Audible: 2 beeps per second

Visual: 2 flashes per second

Vibration: 2 vibrations per 2d

Automatic Zero Reminder for O_ii Models

For O₂ models simply, the Automatic Cipher Reminder is displayed when more than 24 hours have elapsed since the last successful cipher procedure was performed.

Top Readings

The peak readings symbol is displayed when the sensor is exposed to a gas concentration that exceeds the warning setpoints. It is no longer displayed when more 24 hours have passed since the last alarm, or when a successful bump test is performed via an IntelliDoX or MicroDock II station.

Not-compliance Symbol and LED Indicators

The not-compliance warning symbol is displayed when:

• an internal diagnostic test fails;
• a bump test, calibration or zippo procedure fails;
• a bump test or calibration is due, if enabled;
• the sensor is exposed to a gas concentration that exceeds alarm setpoints, if enabled.

The non-compliance alert symbol is no longer displayed when more 24 hours have passed since the concluding alarm, or when a successful bump test or calibration is performed (manual calibration or via an IntelliDoX or MicroDock II station). The non-compliance alarm symbol is permanently displayed when the service-life inaugural reaches 24 hours or less earlier death, and for up to thirty days after expiry.

When Non-compliance after gas exposure is enabled through Armada Manager II via an IntelliDoX station, the LEDs flash in an alternating blueprint when the non-compliance warning symbol is displayed. When the symbol is first displayed, the top LEDs wink. After 30 seconds, the side LEDs flash. After 30 seconds, the pattern repeats until the noncompliance warning symbol is no longer displayed.

Notation: When the detector is crash-land tested via a MicroDock II station, an abnormal test event may occur if non-compliance LEDs are flashing. To suspend the flashing for up to 10 minutes, printing and release the pushbutton. When the flashing stops, insert the detector and perform the test. If the bump exam fails, the LEDs resume flashing.

Recall Events and Settings

When the detector is in normal operating manner, press the pushbutton at any time to scroll through events and settings that are non empty or disabled through Fleet Director Ii via an IntelliDoX station. BW Clip Real Time flashes, vibrates and beeps.
While an issue or setting is displayed, printing the pushbutton to roll to the next available event or setting. If you do not press the pushbutton, or if y'all take reached the terminal available upshot or setting, the detector returns to normal operation. Events and settings are displayed in this order:

1. Superlative Reading, if available, and when a maximum gas exposure outcome has occurred inside the past 24 hours.
2. Time of Height Reading, if Existent-time Clock display is enabled.
3. Operating Life, the remaining operating life of the detector in months, days or hours.
4. Low Alert Setpoint
5. High Alert Setpoint
6. Real-time Clock, if enabled.
7. Firmware Version
8. Next Bump Due, if enabled.
9. Next Calibration Due, if enabled.
10. Hibernation, for 2-twelvemonth H_twoS and CO models only

Zero the Sensor

Over time and through employ, the sensor baseline at zero exposure may drift from the manufacturer's baseline. For optimal performance of O₂ models, BW recommends that you zero the O₂ sensor once every 24 hours or when the Automatic Zero Reminder is displayed. For all other models, BW recommends that you zero the sensor periodically.

Nada Process

1. Move to a normal atmosphere (20.9% v/five O_two ) that is costless of hazardous gas.
2. Press and hold the pushbutton until a 5 second countdown is displayed, and then continue to hold until the countdown is complete.
3. When the countdown is complete, the Null procedure begins and ZErO is displayed.
4. When Zero is successful, PASS and and then CAL ? is displayed. Printing the pushbutton to calibrate, or wait for the detector to enter normal operating fashion after a 5 second inaugural.
5. If Goose egg is non successful, the non-compliance LED flashes. FAIL and the non-compliance alert symbol are displayed. Press the pushbutton to acknowledge the outcome and return to normal performance. The non-compliance warning symbol is displayed and the non-compliance LED flashes. Perform the Zero procedure again. If the procedure fails over again, contact BW.

Bump Tests

When the detector is configured to brandish a bump test reminder, the bump exam symbol is displayed when a bump exam is due. For all-time results, bump examination the detector via an IntelliDoX or MicroDock Ii station. Crash-land tests performed via an IntelliDoX or MicroDock II station are logged every bit bump tests. Manual bump tests are logged as dangerous gas concentrations.

Scale

By default, BW Prune Real Time is configured to apply the following calibration gas mixtures:

You lot can utilize Fleet Manager II software via an IntelliDoX station to alter a detector'southward default scale gas mixtures. If the detector's default scale mixtures were changed, utilize the gas mixture values from Armada Manager II to calibrate the detector.

1. Move to a normal temper (xx.9% 5/v O₂ ) that is free of hazardous gas.
2. Connect the calibration hose to the gas cylinder and to the intake inlet on the calibration cap.
3. Printing and hold the pushbutton until a 5 second inaugural is displayed, and then continue to hold until the countdown is consummate. The naught procedure begins and ZErO is displayed. When Zilch is successful, PASS is displayed.
4. When CAL ? is displayed, press the pushbutton to begin calibration.
5. Put the calibration cap on the sensor grill.
6. When GAS ? is displayed, apply calibration gas for ii minutes at a recommended flow rate of 500 ml/min. When calibration is successful, Pass is displayed and the detector returns to normal operating fashion.

If calibration fails, not-compliance warning symbols are displayed. Press the pushbutton to acknowledge. Repeat calibration. If it fails once more, contact BW.

Event Logs

The detector stores the last 35 events that occurred, including pinnacle readings, bump tests, calibrations and auto zeros. Each record contains:

• detector serial number, sensor type and life-remaining;
• total number of events that take occurred;
• consequence type and duration;
• alert level(s) in ppm or %;
• time elapsed since the alert occurred in days/hours/minutes;
• duration of the alarm (minutes/seconds).

Use Fleet Manager Ii via an IntelliDoX or MicroDock II station to transfer outcome logs from the detector to a computer. When logs are transferred via an IntelliDoX station, the almost contempo 35 events are transferred. When logs are transferred via a MicroDock Ii station, the most recent x events are transferred.

Optional Settings

Apply Fleet Managing director II via an IntelliDoX station to enable the post-obit optional settings for BW Prune Existent Fourth dimension detectors.

Non-compliance After Gas Exposure

When Non-compliance after gas exposure is enabled, the LEDs wink in an alternating pattern when the sensor is exposed to a gas concentration that exceeds alarm setpoints. When the gas exposure is detected, the top LEDs wink. Subsequently 30 seconds, the side LEDs wink. After 30 seconds, the blueprint repeats until more than 24 hours have passed since the terminal alarm, or when a successful crash-land test is performed via an IntelliDoX or MicroDock II station.

Existent-fourth dimension Clock Display

When real-fourth dimension Clock Display is enabled, y'all can display the current time past pressing the pushbutton to Recollect Events and Settings, and then continuing to press the pushbutton until the time is displayed. Time may be displayed in 12-hour or 24-hour clock format.

Hibernation

Hibernation is a manufactory installed characteristic that is bachelor for 24-month H₂S and CO detectors. When Hibernation is activated, the operating life countdown is suspended. Use Hibernation to deactivate the detector for 7 days or longer, up to a maximum of 12 months. When Hibernation is activated, all detector prophylactic functions are disabled.

Activate Hibernation via BW Clip Real Fourth dimension Hibernation Case

1. Have set a BW Clip Hibernation Case. To purchase a Case, contact BW or an authorized distributor.
2. Move to a normal atmosphere (twenty.9% v/v O₂ ) that is free of hazardous gas.
3. Verify that the detector is in normal operating mode.
4. Press the pushbutton to Recall Events and Settings, then continue to press the pushbutton until Hib is displayed.
5. While Hib is displayed, printing the pushbutton until a 5 second countdown is displayed. When the countdown is consummate, the 20-second Hibernation counter is displayed.
6. While the Hibernation counter is displayed, place the detector into a BW Clip Real Fourth dimension Hibernation Instance so close the case firmly. The detector enters Hibernation mode. All detector safety functions are disabled.
7. To reactivate the detector, open the instance and remove the detector.

Actuate Hibernation through Armada Manager II via IntelliDoX

1. Use Fleet Managing director II to activate Hibernation on Insertion via an IntelliDoX station, and then insert the detector in the configured station. The detector event logs are retrieved, and the detector enters Hibernation mode. All condom functions are disabled, and the detector may exist removed from the IntelliDoX station.
2. To reactivate the detector, printing and hold the pushbutton until a 5 2nd inaugural is displayed, and and then go along to hold until the LCD and LEDs turn on and off. The detector performs a self-diagnostic test. When the examination is successful, the type of gas detected and the remaining operating life are displayed. The detector is in normal operating style.
3. For more information, refer to the operator manuals for the IntelliDoX station and Armada Manager 2 software version 4.2 or higher.

Documents / Resources

References

freelbefookeery.blogspot.com

Source: https://manuals.plus/_bw/bwc2-h-clip-real-time-single-gas-detector-for-h2s-co-o2-and-so2-manual

Share this post